74 FORD F100 460 REVERSE PATTERN FULL MANUAL VALVE BODY by Rossana Kirk. Balsa USA 1/3 Scale Ercoupe Repost Like. By Rossana Kirk. Aug 28, 2017 Build with confidence using Balsa USA's Video Manual!!! Don't be afraid to try your hand at Giant Scale building, or just building in general using Balsa. Find best value and selection for your Balsa USA 1 3 Scale Ercoupe Ultimate Kit Nice search on eBay. World's leading marketplace. There are several different interiors for the Ercoupe. The guages in place then put a backer on of 1/16' balsa and tack glue that in place.

• MS:176 ASSEMBLY MANUAL “Graphics and specifications may change without notice”. Specifications: Wing span ------------------------------98.4in (250cm). Wing area ----------------1576.4sq.in (101.7sq dm). Weight ----------------------13.2-15.4lbs (6.0-7.0kg). Length ------------------------------67.3in (171.0cm).

Engine ------------------ -----------33-40cc. Radio -------------------6 channels with 7 servos. • Thank you for choosing the ERCOUPE ARTF by SEAGULL MODELS COMPANY LTD. The ERCOUPE was designed with the intermediate/advanced sport flyer in mind. It is a semi scale airplane which is easy to fly and quick to assemble. The airframe is conventionally built using balsa, plywood to make it stronger than the average ARTF, yet the design allows the aeroplane to be kept light.

• www.seagullmodels.com INSTALL THE AILERONS CONTROL CONTENTS.TS HORN. Fuselage 1) Locate the hardware necessary to install Wing Set the control horns for the ailerons. Tail Set Cowling Main Landing Gear Wing Tube Hardware Set Fiberglass Wheel Pants Canopy Pilot Fuel Tank Fiberglass control horn 2)Position the Control horn on the Aileron and use 30-minute Epoxy. • Instruction Manual. ERCOUPE Position the Control horn on the Aileron and Rudder control horn. Use 30-minute Epoxy Epoxy. INSTALLING THE FUSELAGE SERVOS.

Because the size of servos differ, you may need to adjust the size of the precut open- ing in the mount. The notch in the sides of the mount allow the servo lead to pass through. • www.seagullmodels.com INSTALLING THE STOPPER ASSEMBLY.

Throttle servo arm. 1) Using a modeling knife, carefully cut off the rear portion of one of the 3 nylon tubes leaving 1/2” protruding from the rear of the stopper. This will be the fuel pick up tube.

2) Using a modeling knife, cut one length of silicon fuel line. • Instruction Manual. ERCOUPE 8) Use plywood template to hold in place 3) Carefully bend the second nylon tube the fuel tank with C/A glue to secure the fuel up at a 45º angle. This tube is the vent tube.

Tank inside the fuselage. • www.seagullmodels.com MOUNTING THE ENGINE. 5 x 80 mm 150mm 5.2mm 5x80mm. • Instruction Manual. ERCOUPE 2)Install nose landing gear and wheel pant.

Thread locker glue. NOSE LANDING GEAR INSTALLTION.

5.2mm 1)Locate the items necessary to attach the nose landing gear that are included with your model. • www.seagullmodels.com Axle. Wheel collar wheel 3)Install nose landing gear at the top Fuselage. 3)Install nose landing gear at the top Fuselage. • Instruction Manual. ERCOUPE COWLING.

1)Slide the fiberglass cowl over the engine and line up the back edge of the cowl with the marks you made on the fuselage then trim and cut as shown. Trim and cut. Fallout2 High Resolution Patch. Because of the size of the cowl, it may be nec- essary to use a needle valve extension for the high speed needle valve. • www.seagullmodels.com 2) While keeping the back edge of the INSTALLING THE SPINNER. Cowl flush with the marks, align the front of Install the spinner backplate, propeller and the cowl with the crankshaft of the engine. The spinner cone. Front of the cowl should be positioned so the crankshaft is in nearly the middle of the cowl opening.

• Instruction Manual. ERCOUPE 4) Apply 2-3 drops of thin C/A to each of the Servos. Small weight. Mounting holes. Allow the C/A to cure without using accelerator. Because the size of servos differ, you may need to adjust the size of the precut open- ing in the mount. • www.seagullmodels.com 9) Set the aileron hatch in place and use a 8) A string has been provided in the wing to Phillips screw driver to install it with four wood pull the aileron lead through to the wing root.

Remove the string from the wing at the servo location and use the tape to attach it to the servo extension lead. • Instruction Manual. ERCOUPE LANDING GEAR INSTALLTION. 1)Locate the items necessary to attach the landing gear that are included with your model. 1)Locate the items necessary to attach the 2 mm landing gear that are included with your model. Epoxy M3 X 25 mm. • www.seagullmodels.com Thread locker glue 3x10 mm 5.2mm 5.2mm.

• Instruction Manual. ERCOUPE TAIL SET INSTALLTION. ATTACHMENT TAIL SET-FUSELAGE. • www.seagullmodels.com Elevator pushrod.

Control horn. 4x45mm Metal clevis. ELEVATOR PUSHROD HORN ELEVATOR PUSHROD HORN INSTALLATION. 1) Install the elevator control horn using the same method as with the aileron control horns. 2) Position the elevator control horn on the both side of elevator. • Instruction Manual. ERCOUPE INSTALLATION PILOT AND CANOPY.